Discover XQ-Power Servos in Our eBay Store!
Shop Now
Technical Specifications
Last Updated: 2026-10-08| Identity | |
| Brand |  |
| Product Number | 35084S |
| Category | Hobby |
| Discontinued | Yes |
| Performance | |
| Torque |
6.0V
26.00 oz-in
1.87 kg-cm
0.2 N-m
4.8V
21.00 oz-in
1.51 kg-cm
0.1 N-m
|
| Speed |
6.0V
0.05 sec/60°
1,200.0 deg/s
200.0 RPM
4.8V
0.07 sec/60°
857.1 deg/s
142.9 RPM
|
| Physical | |
| Weight | 0.76 oz21.5 gBottom 10% |
| Dimensions |
L 1.14 in W 0.51 in H 1.18 in L 29.0 mm W 13.0 mm H 30.0 mm |
| Drivetrain | |
| Motor Type | 3-pole |
| Gears | Metal |
| Gear Spline/Teeth | 24 T estimate |
| Rotation/Support | Single Bearing |
| Control & Signal | |
| Modulation | Digital |
| Rotational Range | 180° |
| Pulse Cycle | 20 ms |
| Pulse Width | 900-2100 µs |
| Connectivity | |
| Connector | JR (Universal) |
Disclaimer: Most data is sourced from the manufacturer. Some data is sourced from our loyal community and with the help of AI. We aim for accuracy but are not responsible for inaccurate information.
Class Comparison
| Weight | Bottom 10% Lighter than 5% of 620 Digital Micro servos |
Performance Analysis
| Shaft Power | 0.55–0.96 W |
| Power Density | 1.402 W/in³ More power-dense than 35% of 590 Digital Micro servos |
| Torque Density | 0.9767 oz-in/g |
| Torque-to-Volume Ratio | 30.61 oz-in/in³ |
| Speed-to-Weight | 0.66445 (1/sec·g) |
| Speed-Torque Trade-off | 1.47 |
Similar Active Servos
Reviews (5)
-
2cool
November 8, 2017Application(s): 450 align
Comments: Is this the correct setting for a HSG 5084mg pulse rate 1520us HZ333 correct in a Ikon controller
syberbruno
April 28, 2013Application(s): Tailservo Helicopter
Comments: HSG5084MG servo works absolute perfect with my Spartan Quark Gyro in my Walkera HIKO 400 Helicopter
The chosen Framerate is 1520 / 333Hz2Doggs
September 26, 2012Application(s): Tail servo on 450 Pro
Comments: This servo worked really well on my 450 Pro tail, running at 6v and 333Hz with a CX 3x1000 fbl controller. It was noticeably better than any of the 9257 clones I'd tried up to then - but burned out after maybe fifty flights. The tail linkage was good, with no binding. The servo was actually a warranty replacement from Hitec for one, originally purchased on eBay, that failed when used on the tail of a Mini Titan using a CSM 420e gyro, set to 6v and 333Hz.
If it hadn't failed, I think I would have given it a five star rating.
Chantheman84
April 18, 2011Application(s): Trex 450 SeV2
Comments: Real good servo, dead on and solid
MarkRocketman
May 12, 2010Application(s): Tail servo Blade 400 and Trex 450
Comments: Hitec HSG-5084MG A perfect partner to a Futaba 401 Gyro. Fast accurate producing a razor sharp heading lock without too much dialling on 400 -450 Heli. + 6V