Discover XQ-Power Servos in Our eBay Store!
Shop Now
Technical Specifications
Last Updated: 2026-09-16| Identity | |
| Brand |  |
| Product Number | 35065S |
| Category | Hobby |
| Performance | |
| Torque |
6.0V
31.00 oz-in
2.23 kg-cm
0.2 N-m
4.8V
25.00 oz-in
1.80 kg-cm
0.2 N-m
Average
|
| Speed |
6.0V
0.11 sec/60°
545.5 deg/s
90.9 RPM
4.8V
0.14 sec/60°
428.6 deg/s
71.4 RPM
Below Average
|
| Running Current |
6.0V
0.220 A
220 mA
4.8V
0.180 A
180 mA
Average
|
| Stall Current | 0.96–1.2 A960–1200 mAAverage |
| Physical | |
| Weight | 0.42 oz11.9 gAverage |
| Dimensions |
L 0.92 in W 0.45 in H 0.94 in L 23.4 mm W 11.4 mm H 23.9 mm |
| Case Material | Plastic |
| Drivetrain | |
| Motor Type | 3-pole |
| Gears | Metal |
| Gear Spline/Teeth | 24 T estimate |
| Shaft Size | 5.0 mm |
| Rotation Mode | Positional |
| Rotation/Support | Single Bearing |
| Control & Signal | |
| Modulation | Digital |
| Direction | Clockwise |
| Rotational Range | 80° |
| Pulse Cycle | 20 ms |
| Pulse Width | 900-2100 µs |
| Neutral Position | 1500 µs |
| Dead Band | 2 µs |
| Angle Sensor | Potentiometer |
| Control System | PWM |
| Programmable | Yes |
| Signal Voltage | 3-5V |
| Electrical & Environment | |
| Operating Voltage | 4.8–6 V |
| Temperature | -20–60 °C-4–140 °F |
| Idle Current | 0.003 A3 mA |
| Connectivity | |
| Connector | S |
| Wire Length | 160 mm6.3 in |
Disclaimer: Most data is sourced from the manufacturer. Some data is sourced from our loyal community and with the help of AI. We aim for accuracy but are not responsible for inaccurate information.
Class Comparison
| Torque | Average Stronger than 45% of 349 Digital Micro servos at 4.8V |
| Speed | Below Average Faster than 25% of 347 Digital Micro servos at 4.8V |
| Weight | Average Lighter than 46% of 597 Digital Micro servos |
| Running Current | Average Lower draw than 49% of 60 Digital Micro servos at 4.8V |
| Stall Current | Average Lower draw than 47% of 188 Digital Micro servos |
Performance Analysis
| Shaft Power | 0.33–0.52 W |
| Power Density | 1.339 W/in³ More power-dense than 32% of 563 Digital Micro servos |
| Torque Density | 2.1008 oz-in/g Stronger than 34% of 349 Digital Micro servos |
| Torque-to-Volume Ratio | 64.24 oz-in/in³ Denser torque than 37% of 345 Digital Micro servos |
| Speed-to-Weight | 0.60024 (1/sec·g) Faster than 34% of 347 Digital Micro servos |
| Speed-Torque Trade-off | 3.50 Better balanced than 56% of 345 Digital Micro servos |
| Current-per-Torque Ratio | 0.0480 A/oz-in More efficient than 35% of 98 Digital Micro servos |
| Idle-to-Running Current Ratio | 0.017 5th-highest idle-to-running current ratio of 42 Digital Micro servos |
| No-Load vs Stall Current Spread | 6.67 Narrower current spread than 70% of 45 Digital Micro servos |
| Torque Gain per Volt | 20.00%/V More voltage-responsive (torque) than 69% of 290 Digital Micro servos |
| Speed Gain per Volt | 22.73%/V More voltage-responsive (speed) than 76% of 295 Digital Micro servos |
| Voltage Range Width | 1.2 V Wider voltage range than 41% of 496 Digital Micro servos |
| Dead-Band-to-Pulse-Width Ratio | 0.0017 Finer dead band than 46% of 182 Digital Micro servos |
Similar Active Servos
Reviews (2)
Includes 1 review aggregated from around the web.
Popular for small aircraft, micro helicopters and robotics. Praised for resolution, centering and holding strength. It is expensive for its size.
-
MattFL
July 30, 2011Application(s): Cyclic on a TREX 450 sport
Comments: My Align TREX 450 Sport Super Combo kit included 3 Align DS410M servos for cyclic control. 6 of them died on me. Based on my positive experience with a HiTech servo in my nitro buggy, I bought a set of HS5065-MG servos to replace the DS410M's. So far I have many flights and not a single failure. Also the 5065MG's are much more accurate. The best way to explain is they seem to have less play in them than the Align DS410M's did. Every little stick movement causes a reaction in the heli, this makes it easier to fly when you're trying to be precise. So in short, at this point I am very satisfied with these 5065-MG's and I would recommend them for cyclic control on a 450 sized heli. Note that I have only bee flying heli's for about 7 months so I'm not a fantastic pilot and I cannot comment on how these work under inteanse 3D flight, but for general flying around they are great.